Purple Resin 1 Second 420nm 480nm Dental Light Cure Unit

1Second LED Dental Light Cure Unit Lamp High Intensity Purple Resin Lamp

Specification:
 
1. High power LED,professional dental spectrum
2. Bionic design,LCD display
3. Optional working mode: strong, low, gradually strong, flashing
4. Solidifying time:5-40s,can be adjustable
5. Temperature inspect, over-temperature protection
6. High capacity Li-ion battery , and can charge with charge base or adaptor

Technical Datas:

Installation and Removal methods

4.1 Align the large end of the light guide (front connector) with the mounting hole on the upper end of the light curing machine and insert it (it must be inserted to the bottom in a rotating manner, not diagonally).
4.1 Align the large end of the light guide (front connector) with the mounting hole on the upper end of the light curing machine and insert it (it must be inserted to the bottom in a rotating manner, not diagonally).
4.2 Put the secondary film on the machine.
4.2 Set the secondary film on the machine.
4.3 When charging is needed, take out the charging base and power adapter, connect the adapter to the 100-240VAC network, and insert the output plug of the adapter into the charging base logo
4.3 When charging is needed, take out the charging dock and power adapter, connect the adapter to 100-240 VAC network power, and insert the output plug of the adapter into the charging dock logo
It is a DC 5.0V charging jack, and the host can be charged by putting it into the charging base. When charging is not required, please unplug the power adapter.
It is a DC 5.0V charging jack, which can be charged by putting the host into the charging base. When charging is unnecessary, please unplug the power adapter.

Operation Method:

5.1 Press the power switch button ("I") to boot.
5.1 Press the power switch button ("I") to boot.
5.2 Mode setting: lightly press the mode setting key ("M") to change the operating mode, the light curing machine will work in the set mode, irradiating different intensities
5.2 Mode setting: lightly press the mode setting key ("M") to change the operating mode, the light curing machine will work in the set mode, irradiating different intensities
Blu-ray, the available modes are shown in Table 1.
Work should be stopped until the handle is completely cooled down before starting to work. It is recommended that the number of continuous irradiation should not exceed 10 times.
5.3 Time setting: lightly press the time setting key ("T") to set the curing time. See Table 1 for the settable curing time.
Blu-ray, the available modes are shown in Table 1.
5.4 When using, put the disposable film sleeve into the head of the main unit.
5.3 Time setting: lightly press the time setting key ("T") to set the curing time. The settable curing time is shown in Table 1.
5.5 Then align the light source of the light guide (front connector) at the position that needs to be cured, press the power switch button ("!"), the host emits a beep
5.4 When using, put the disposable film sleeve into the head of the host.
The host emits blue light and works according to the selected working mode. The digital display starts to display the countdown time from the selected timing time and ends at 0:00
5.5 Then point the light guide rod (front connector) light source at the position that needs to be cured, press the power switch button ("!"), the host emits a beep
Work, the digital display returns to display the set timing time.
The host emits blue light and works according to the selected working mode. The digital display starts to display the countdown time from the selected timing time and ends at 0:00
5.6 After the normal use, before the timing time is over, press the power switch button ("I") to end the work and turn off the output at any time.
Work, the digital display returns to display the set timing time.
5.7 After an irradiation cycle is over, you can press the power switch button ("1") immediately to start the next irradiation cycle, if it is obvious that the handle starts to become hot
5.6 After normal use, before the timing time is over, press the power switch button ("i") to end the work at any time and turn off the output.
Work should be stopped until the handle is completely cooled down before starting to work. It is recommended that the number of continuous irradiations should not exceed 10 times.
5.7 After an irradiation cycle is over, you can press the power switch button ("1") immediately to start the next irradiation cycle, if it is obvious that the handle starts to become hot

5.8 Low voltage indication: The host has a low battery detection function. When a low battery is detected, the digital tube flashes. Please charge it in time.
5.9 If the transparent cover is stained with resin after use, please wipe it with a cotton cloth to avoid affecting the light intensity.
5.10 The machine will automatically shut down after 2 minutes of inactivity. To turn it on, press N/0ff.
5.11 The effective light intensity of this machine is many times higher than that of the halogen lamp curing machine, and the curing depth of the light-curing composite resin is not less than 4mm for 10 seconds.
5.12 The front connector at the front end can be removed, but high temperature and high pressure sterilization is not allowed, otherwise it will cause damage.

Transportation, storage and maintenance

6.1.1 During transportation, avoid excessive shock and vibration, handle with care and avoid inversion.
6.1.2 It should not be mixed with dangerous goods during transportation.
6.1.3 Avoid sunlight, rain or snow during transportation. .

6.2 Store in
6.2.1 Do not mix with toxic, corrosive, flammable, or explosive materials during storage.
6.2.2 The product should be stored in an environment where the relative humidity does not exceed 10%~93%, the atmospheric pressure is 70 kPa~106 kPa, and the temperature is -20°C~+40°C.
6.3 Maintenance
6.3.1 This equipment should be handled with care, far away from the source of the earthquake, and should be installed or stored in a cool, dry and ventilated place.
6. 3.2 When the equipment is not in use, the power switch should be turned off and the power plug should be unplugged; when it is not in use for a long time, it should be powered on every 3 months for five minutes each time.
6.3.3 To clean or disinfect, wipe the surface with clean water or disinfectant, do not soak.
6.3.4 After each use, check whether there is any resin remaining on the surface of the front joint, so as not to affect the life of the front joint or affect the curing effect.